asphalt mix specifications

Item 340 Dense-Graded Hot-Mix Asphalt - City of Round Rock

aggregate and asphalt binder mixed hot in a mixing plant. This specification is intended for small quantity. (SQ) HMA projects, typically under 5,000 tons total ...

Learn More
Hot-Mix Asphalt Material Properties

Hot-Mix Asphalt Material Properties . SCDOT Designation: SC-M-402 (03/11) 1. SCOPE. 1.1 Use the following specifications for preparing, constructing, and accepting Hot-Mix Asphalt (HMA) material properties. NOTE: Refer to the Standard Specifications, Division 300 for HMA Base Courses and on 400 for HMA Surface and Divisi ...

Learn More
UNHSC Design Specifications for Porous Asphalt Pavement

D. Alternative specifications for mix, such as Open Graded Friction Courses (OGFC) from Federal Agencies or state Departments of Transportation (DOT), may be used if approved by the Engineer. The primary requirements for the specifications of the mix are performance grade (PG) asphalt

Learn More
Section 400 BITUMINOUS PAVEMENTS

3. When slag aggregates are used in the mix, the asphalt content shall be increased accordingly5 minimum 25 percent for an all slag mix. 4. The asphalt content job mix tolerance of ±0.4% shall not apply to Marshall Design mixtures. 5. Asphalt cement 702-0600 may be substituted for 702-0500 in the counties of Clinton, Essex, Franklin,

Learn More
Asphalt Pavement Construction | Asphalt Institute

Is the hot mix asphalt surface stiff enough to resist deformation (ruts or ... agency specifications will spell out a minimum acceptable temperature for the mix.

Learn More
PDF Construction Specification for Hot Mix Asphalt Sidewalks

The hot mix shall be placed on the prepared granular base according to section 311.07 of OPSS 311, except that the asphalt emulsion, used in resurfacing sidewalks, shall be according to TS 3.30.05.02, herein. TS 3.30.07.01 Asphalt Sidewalk Asphalt sidewalks shall be constructed with 150 mm of Granular A and 80 mm of Superpave 12.5 asphalt.

Learn More
ITEM NO. 206S - ASPHALT STABILIZED BASE 9-26-12

The aggregate shall meet all requirements of and conform to Type A of Specification Item 340S, "Hot Mix Asphalt Concrete Pavement". When shown on the ...

Learn More
Implementation Guide IG – 8 - AAPA

publications such as APRG 18, AAPA National Asphalt Specification, Austroads Framework for. Specifying Asphalt, AS 2150 - Hot Mix Asphalt, and various other ...

Learn More
STANDARD CONSTRUCTION SPECIFICATIONS FOR ASPHALT

The following standards of The Asphalt Institute are also a part of these Specifications: Construction Specifications for Asphalt Concrete, by The Asphalt Institute. Mix Design Methods for Asphalt Concrete, by The Asphalt …

Learn More
PDF Part R27 Supply of Asphalt Contents

"Asphalt Mix Design Assessment" is a documented assessment of a submitted asphalt mix design with an Asphalt Mix Register Number provided by DPTI. "Asphalt Mix Register Number" is a mix approval number provided by DPTI to an accepted nominated mix. All mixes are placed on DPTI's Asphalt Mix Register and monitored by DPTI.

Learn More
ITEM NO. 206S - ASPHALT STABILIZED BASE 9-26-12 | Standard

The aggregate shall meet all requirements of and conform to Type A of Specification Item 340S, "Hot Mix Asphalt Concrete Pavement". When shown on the ...

Learn More
AASHTO - M 320 - Standard Specification for Performance

This specification covers asphalt binders graded by performance. Grading designations are related to the average seven-day maximum pavement design temperature and the minimum pavement design temperature. This specification contains Table 1 and Table 2. If no table is specified, the default is Table 1.

Learn More
PDF Hot Mix Asphalt Pavement Design Guide

HOT MIX ASPHALT SPECIFICATIONS All work involving hot mix asphalt pavements and resurfacing can be covered by using the Maryland State Highway Administration July 2008 Standard Specifications for Construction and Materials in conjunction with the typical sections that follow.

Learn More
TxDOT Specifications

Nov 15, 2006 · REFERENCE ITEMS (210), (300), (301), (320), (520), (585) Go to Top. 341 - DENSE GRADED HOT MIX ASPHALT (QCQA) SPECIFICATION REQUIREMENTS 1) Specify the type and grade of Performance Grade (PG) asphalt binder on the set of plans. 2) If different aggregate quality requirements (listed in Table 1) are desired, specify on the set of plans. 3) Specify the surface aggregate …

Learn More
PDF Georgia DOT Asphalt Pavement Selection Guidelines

The list of qualified bituminous materials is QPL-7. The type of asphalt binder for each mix will be included on the approved GDOT Job Mix Formula for each type of mix. Specifications for asphalt cement are located in Section 820 of the GDOT Specifications. Specifications for cationic asphalt emulsions are located in Section 824 of the GDOT

Learn More
asphalt mix design - Main Roads

510.11 RECLAIMED ASPHALT PAVEMENT. RAP shall meet the requirements of Specification 511 MATERIALS FOR BITUMINOUS TREATMENTS, including ...

Learn More
Hot Mix Asphalt Pavement entirely replaces the following

2005年3月10日 — Massachusetts Highway Department. 2005 Quality Assurance Specifications for Hot Mix Asphalt Pavement. Section 450 – HMA Pavement (No ...

Learn More
460 Hot Mix Asphalt Pavement - Wisconsin Department of

2021 Standard Specifications. 460 Hot Mix Asphalt Pavement. 460.1 Description. (1) This section describes HMA mixture design, providing and maintaining a ...

Learn More
specification 1142 bituminous cold mix - Hornsby Shire Council

2020年10月11日 — General: Provide bituminous cold mix as documented. Performance. Quality: Requirements for quality control and testing, including maximum lot ...

Learn More
Specification 3.50 Asphalt Concrete Pavement - EPS - Transportation

20 Jun 2002 ... The Job Mix Formula establishes the aggregate proportioning, target aggregate gradation and approved asphalt content to be used for ...

Learn More

Leave a comment